Re: Monitor power supplies...
what is the result when you try the following snmp oid? can you get two results?? should be Power Supply 1 and Power Supply 2 1.3.6.1.4.1.9.9.13.1.5.1.3
View Articlemonitoring cisco ucs
I am using npm 10.3 and tring to onitor cisco ucs fabric interconnects and blades. I have 2 fabric interconnects and one cluster ip. i added all 3 ips. but when i go to each ip, i only see one switch...
View ArticleRe: Monitor power supplies...
Cisco hasn't always been consistent across differing model lines when it comes to which OIDs represent power supplies and fans.Which chassis are you looking to monitor?
View ArticleRe: Adv Alerts based on Syslog messages?
So there is not a way to send an alert based on syslog messages? Jeff
View ArticleRe: Adv Alerts based on Syslog messages?
Sure- if you open Syslog Viewer on your NPM server, go to View->Alerts/Filter Rules
View ArticleRe: npm 10.0 can use for esx5.1?
It certainly does, however you will likely need to manually configure SNMP on the ESXi box (Configuring SNMP v1/v2c/v3 Using ESXCLI 5.1 | VMware vSphere Blog - VMware Blogs)I would suggest upgrading to...
View ArticleRe: Adv Alerts based on Syslog messages?
Yes using either:a) a custom SQL alert based on the node.in the custom SQL have something like: WHERE nodeid IN ( SELECT DISTINCT nodeid FROM syslog WHERE acknowledged = 0 AND syslogseverity...
View ArticleRe: Interface physical address changed?
I upgraded to NPM 10.5 and it seems to have helped with this issue.
View ArticleRe: Interface physical address changed?
One of the reasons you have a setting in NPM for "device rediscovery" (set to 30 min by default) is for this. Every so often, a device will re-number the interfaces (this goes for NICs and also for...
View ArticleClik here to view.
Does APM_HardwareItems table have current updated values?
I would like to know if the above mentioned table does have the current value for the hardware. I'm looking to put together a report that shows the current utilization of the power supplies to check...
View ArticleClik here to view.
Re: Alert when ESX Status in equal to UP
This worked awesome. Injecting the Join in the From part is Genius!!
View ArticleRe: Monitor power supplies...
For the 4500's, 6500'sand 7600 I use 1.3.6.1.4.1.9.9.13.1.5.1.3 ciscoEnvMonSupplyStateI don't have any 3500s to test with. When you create your UnDP, use MIB value Type "Raw Value", SNMP Get Type "Get...
View ArticleRe: Does APM_HardwareItems table have current updated values?
Thank you! I just wanted to confirm that the latest polled values would be in that table for my report. Here's what I've got so far. SELECT IP_Address ,Caption ,SysName ,DisplayName...
View ArticleNPM 10.5 - custom Propety Editor - few nigglies..
Hi SW finally upgraded to 10.5 and the new web CPE is good. far better than whenyou first tried to release the web CPU LOL. anyway, few things you need to fix 1. when you change from Managed...
View ArticleRe: Fortinet hardware monitoring
No, I used the built-in support. With FortiOS 4, when you would have NPM do a List Resources, the CPU, memory, and about 4 disk drives/spaces would show up. With the release of FortiOS 5, that does...
View ArticleCustomized Views
I am looking to make a customized summary page that shows detailed interface statistics. However when the summary view type is selected there almost no interface statistic options available that give...
View ArticleRe: Training
I took training at Loop1 Systems just about a year ago and thought it was amazing. I inherited network monitoring when we had a staff change and needed to get up to speed extremely quick. The...
View ArticleRe: Customized Views
Have you tried the multiple object charts? Outside of that, on a summary view, you are looking at reports. Thanks,Chrystal Taylorhttp://www.loop1systems.com
View Article